Showing results: 166 - 180 of 241 items found.
-
M8049A -
Keysight Technologies
The M8049A ISI channel boards can be used to emulate channel loss in receiver test setups. The boards are used to emulate channel loss for data rates of 32 Gb/s and higher. A choice of 21 PC board traces with different lengths can be inserted into the signal path. The trace lengths range from 0.8 inch (20.3 mm) to 22.3 inch (566.4 mm). By cascading the traces within one board or with another board, a wide range of channels can be emulated with very fine resolution of insertion loss steps. With their small size the ISI channel boards can be located closely to the device under test.
-
XF07-518 -
Curtiss-Wright Defense Solutions
The XF07-518 is a rugged quad channel 500MSPS 14-bit digital receiver XMC. The ADC devices are controlled by a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms. The combination of direct high-speed, high-resolution analog I/O port and FPGA processing makes the XF07-518 ideal for demanding applications including radar, imaging and test equipment across commercial and defense market spaces.
-
RF-LiveSim -
TestTree
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
FSMR3000 -
Rohde & Schwarz GmbH & Co. KG
The R&S®FSMR3000 is a microwave measurement receiver to calibrate signal generators and attenuators with one single instrument. Most important features provided are tuned RF level measurements, level measurements, analog modulation and spectrum analysis. Additionally, the R&S®FSMR3000 can be equipped with powerful hardware for high-end phase noise test supplementary to the standard phase noise test with the spectrum analyzer.
-
XF07-516 -
Curtiss-Wright Defense Solutions
The XF07-516 is a rugged quad channel 250MSPS 16-bit digital receiver XMC. The ADC devices directly interfaces to a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms. The combination of direct high-speed, high-resolution analog I/O ports and next FPGA processing makes the XF07-516 ideal for demanding applications including radar, imaging and test equipment across both commercial and defense market spaces.
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
LB301 -
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
E8267D -
Keysight Technologies
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
GWRMT001 -
Grand Wing Servo-tech Co., Ltd.
◆To measure the Pulse Width transmitted by Transmitter for up to 9 channels. ◆To measure the Pulse Width sent from Receiver.◆To test the rotations of Servo automatically – at the pulse widths of top, medium and low points set by user already.◆To test the automatic rotations of Servo.◆To test the rotations of Servo by turning the knob on the tester manually .◆To test the sensitivity of Servo (1μS per step minimum).◆To measure RPM of a spinning propeller – for 2 – 6 blades ones, real time RPM value shown／to set the peak RPM value up to 99990 per minute.◆Shiny 4 digits red LED's to display the values measured.◆Power source can be from UM-4 / AAA cell x4, or an adapter with 7-15V or BEC (5V) from an ESC.◆An output port for applying Positive/Negative signals of Pulse Width from this tester.◆Four buttons for setting up functions and modes.
-
GX3640 -
Terotest Systems Ltd.
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
GX3640 -
Marvin Test Solutions, Inc.
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
Gauss Instruments
The EMI receiver families TDEMI® of GAUSS INSTRUMENTS® provide a huge fully CISPR compliant real-time bandwidth and therefore allow to speed up your measurements tremendously and to reduce the measurement uncertainty significantly - both at the same time. By using the full automation software suite EMI64k from GAUSS INSTRUMENTS the test procedures according to the CISPR 16-2-3 standard for the FFT-based measuring instruments as well as conventional testing (pre-scan and final maximization) and further EMC Standards are available. In comparison to the previously conventional pre-scan and final measurement strategy, the overall test quality can be significantly increased whereas the testing times are reduced by orders of magnitudes.
-
Marvin Test Solutions, Inc.
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Marvin Test Solutions, Inc.
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Marvin Test Solutions, Inc.
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
